User Contributed MET/CAL PROCEDURE ============================================================================= INSTRUMENT: Trig-Tek 203T:Charge Amplifier DATE: 20-Nov-97 AUTHOR: User Contributed REVISION: 0 ADJUSTMENT THRESHOLD: 70% NUMBER OF TESTS: 41 NUMBER OF LINES: 347 CONFIGURATION: Fluke 5700A CONFIGURATION: Datron 1281 STANDARD: DTB 1000pF ============================================================================= STEP FSC RANGE NOMINAL TOLERANCE MOD1 MOD2 3 4 CON # This procedure is run with the MET/CAL Configuration #2 loaded. 1.001 ASK- N P U F W 1.002 ASK+ X 1.003 STD DTB 1000pF 1.004 HEAD INITIAL CONDITIONS 1.005 DISP Connect Model 203T Test card to UUT edge connector. 1.005 DISP Connect UUT power cord and plug in to 1.005 DISP a 120V 60Hz source. 1.006 HEAD {* Charge Amplifier Verification *} 1.007 HEAD {Range 100} 1.008 HEAD {SENSITIVITY dial 10.0} 1.009 HEAD Charge Amplifier Verification 1.010 JMP 2.001 1.011 EVAL 2.001 DISP Set the UUT as follows: 2.001 DISP CAL-OPER ........................... OPER 2.001 DISP SENSITIVITY ........................ X10/ & pc/g 2.001 DISP UNITS .............................. g's 2.001 DISP FULL SCALE ......................... 100 2.002 DISP Set the UUT as follows: 2.002 DISP PEAK-RMS ........................... RMS 2.002 DISP LP FILTER .......................... HIGH 2.002 DISP SENSITIVITY dial ................... 10.0 2.002 DISP FS OUTPUT .......................... 10.0 2.002 DISP SE/DIFF switch ..................... SE 2.003 DISP Connect the 5700 to the ACCEL INPUT (top) 2.003 DISP connector on the Test card through the 1000pF standard 2.003 DISP capacitor. 2.004 DISP Connect the 1281 to the ACCEL OUT (2nd from bottom) 2.004 DISP connector on the UUT test card. 2.005 IEEE [@1281]*RST 2.006 IEEE [@1281]ACV AUTO,FILT40HZ,TFER_OFF 2.007 5700 0.707V 61.4H S 2W 2.008 IEEE [@1281][D5000]RDG?[I] 2.009 MEM* 1000 2.010 ACC 0.2 50.00mV 100P% +20P/ 2.011 MEME 2.012 MEMC mV 1.00U rmsx10 #! Test Tol 1, Sys Tol 0.005004, TUR 199.840 (>= 4.00). 3.001 DISP Set the UUT to PEAK. 3.002 IEEE [@1281]ACV AUTO,FILT40HZ,TFER_OFF 3.003 5700 0.707V 61.4H S 2W 3.004 IEEE [@1281][D5000]RDG?[I] 3.005 MEM* 1000 3.006 ACC 0.2 70.7mV 100P% +20P/ 3.007 MEME 3.008 MEMC mV 1.40U peakx10 #! Test Tol 1.4, Sys Tol 0.007074, TUR 197.908 (>= 4.00). 4.001 HEAD {} 4.002 HEAD {SENSITIVITY dial 1.0} 4.003 DISP Set the SENSITIVITY dial on the UUT to 1.0. 4.004 5700 0.707V 61.4H S 2W 4.005 IEEE [@1281][D5000]RDG?[I] 4.006 ACC 2 .7070V 80P% +10P/ 4.007 MEME 4.008 MEMC V 0.0140U peakx10 #! Test Tol 0.014, Sys Tol 7.656e-005, TUR 182.863 (>= 4.00). 5.001 5700 0.707V 61.4H S 2W 5.002 MEMI Enter the UUT meter reading in g's. 5.003 MATH mem1= 100 5.004 MEME 5.005 MEMC g's 2.0U #! Test Tol 2, Sys Tol 6.0025e-005, TUR 33319.450 (>= 4.00). 6.001 HEAD {SENSITIVITY dial 10.0} 6.002 DISP Set the UUT as follows: 6.002 DISP SENSITIVITY dial ................... 10.0 6.002 DISP SENSITIVITY ........................ X1 6.003 5700 0.707V 61.4H S 2W 6.004 MEMI Enter the UUT meter reading in g's. 6.005 MATH mem1= 100 6.006 MEME 6.007 MEMC g's 2.0U x1 #! Test Tol 2, Sys Tol 6.0025e-005, TUR 33319.450 (>= 4.00). 7.001 IEEE [@1281]DCV AUTO 7.002 5700 0.707V 61.4H S 2W 7.003 DISP Connect the Datron to the DC OUTPUT jack (2nd from top) 7.003 DISP on the UUT test card. 7.004 IEEE [@1281][D1000]X?[I] 7.005 ACC 20 10.000 3P% 0.1P/ 7.006 MEME 7.007 MEMC V 0.200U x1 #! Test Tol 0.2, Sys Tol 3.2e-005, TUR 6250.000 (>= 4.00). 8.001 HEAD {VEL OUTPUT} 8.002 JMP 9.001 8.003 EVAL 9.001 DISP Connect the Datron to to the VEL OUTPUT jack (3rd from 9.001 DISP bottom) on the UUT test card. 9.002 DISP Set the UUT as follows: 9.002 DISP UNITS .............................. IN/SEC 9.003 IEEE [@1281]ACV AUTO FILT40HZ,TFER_OFF 9.004 5700 0.707V 61.4H S 2W 9.005 IEEE [@1281][D5000]RDG?[I] 9.006 ACC 20 10.00V 80P% +10P/ 9.007 MEME 9.008 MEMC V 0.300U in/secx1 #! Test Tol 0.3, Sys Tol 0.001, TUR 300.000 (>= 4.00). 10.001 HEAD {DISP OUTPUT} 10.002 JMP 11.001 10.003 EVAL 11.001 DISP Set the UUT as follows: 11.001 DISP UNITS .............................. MILS 11.002 DISP Connect the Datron to the DISP OUTPUT jack (3rd from 11.002 DISP top) on the UUT test card. 11.003 IEEE [@1281]ACV AUTO,FILT100HZ,TFER_OFF 11.004 5700 0.707V 139.9H S 2W 11.005 IEEE [@1281][D5000]RDG?[I] 11.006 ACC 20 10.00V 80P% +10P/ 11.007 MEME 11.008 MEMC V 0.400U milsx1 #! Test Tol 0.4, Sys Tol 0.001, TUR 400.000 (>= 4.00). 12.001 5700 0.707V 139.9H S 2W 12.002 MEMI Enter the UUT meter indication in MILS. 12.003 MATH mem1=100.0 12.004 MEME 12.005 MEMC mils 5.0U #! Test Tol 5, Sys Tol 6.0025e-005, TUR 83298.626 (>= 4.00). 13.001 DISP Set the UUT as follows: 13.001 DISP UNITS .............................. g's 13.002 5700 0.707V 139.9H S 2W 13.003 MEMI Enter the UUT meter indication in g's. 13.004 MATH mem1=100.0 13.005 MEME 13.006 MEMC g's 2.0U #! Test Tol 2, Sys Tol 6.0025e-005, TUR 33319.450 (>= 4.00). 14.001 HEAD {FULL-SCALE (TAPE) OUTPUT} 14.002 JMP 15.001 14.003 EVAL 15.001 DISP Connect the Datron to the TAPE OUTPUT jack. (bottom) 15.002 5700 0.707V 139.9H S 2W 15.003 IEEE [@1281][D5000]RDG?[I] #15.006 MEM* 1000 15.004 ACC 20 7.07V 80P% +10P/ 15.005 MEME 15.006 MEMC V 0.240U g'sx1 #! Test Tol 0.24, Sys Tol 0.0007656, TUR 313.480 (>= 4.00). 16.001 HEAD {RANGE 30} 16.002 JMP 17.001 16.003 EVAL 17.001 DISP Set the UUT as follows: 17.001 DISP FULL SCALE ......................... 30 17.002 5700 0.211V 139.9H S 2W 17.003 MEMI Enter the meter indication in g's. 17.004 MATH mem1= 30 17.005 MEME 17.006 MEMC g's 0.6U #! Test Tol 0.6, Sys Tol 3.11e-005, TUR 19292.605 (>= 4.00). 18.001 HEAD {RANGE 10} 18.002 JMP 19.001 18.003 EVAL 19.001 DISP Set the UUT as follows: 19.001 DISP FULL SCALE ......................... 10 19.002 5700 70.7mV 139.9H S 2W 19.003 MEMI Enter the meter indication in g's. 19.004 MATH mem1= 10 19.005 MEME 19.006 MEMC g's 0.20U #! Test Tol 0.0002, Sys Tol 1.707e-005, TUR 11.716 (>= 4.00). 20.001 HEAD {RANGE 1} 20.002 JMP 21.001 20.003 EVAL 21.001 DISP Set the UUT as follows: 21.001 DISP FULL SCALE ......................... 1 21.002 5700 7.07mV 139.9H O S 2W 21.003 MEMI Enter the meter indication in g's. 21.004 MATH mem1= 1 21.005 MEME 21.006 MEMC g's 2.00% #! Test Tol 0.0001414, Sys Tol 6.7777e-006, TUR 20.8625 (>= 4.00). 22.001 HEAD {CAL MODE} 22.002 DISP Set the UUT as follows: 22.002 DISP CAL-OPER ........................... CAL 22.002 DISP FULL SCALE ......................... 10 22.003 DISP Disconnect the 5700 from the UUT ACCEL input. 22.004 DISP Connect the 5700 without the 1000pF capacitor to the 22.004 DISP UUT CAL input connector. 22.005 5700 1V 150H S 2W 22.006 MEMI Enter the UUT meter indication. 22.007 MATH mem1=10 22.008 MEME 22.009 MEMC g's 0.20U sensx1 #! Test Tol 0.2, Sys Tol 8.2e-005, TUR 2439.024 (>= 4.00). 23.001 DISP Set the UUT as follows: 23.001 DISP SENSITIVITY ........................ X10 23.002 5700 1V 150H S 2W 23.003 MEMI Enter the UUT meter indication. 23.004 MATH mem1=10 23.005 MEME 23.006 MEMC g's 0.20U sensx10 #! Test Tol 0.2, Sys Tol 8.2e-005, TUR 2439.024 (>= 4.00). 24.001 DISP Set the UUT as follows: 24.001 DISP SENSITIVITY dial.................... 1.0 24.002 5700 1V 150H S 2W 24.003 MEMI Enter the UUT meter indication. 24.004 MATH mem1=10 24.005 MEME 24.006 MEMC g's 0.20U sensx10@1.0 #! Test Tol 0.2, Sys Tol 8.2e-005, TUR 2439.024 (>= 4.00). 25.001 DISP Set the UUT as follows: 25.001 DISP RMS-PEAK ........................... RMS 25.002 5700 1V 150H S 2W 25.003 MEMI Enter the UUT meter indication. 25.004 MATH mem1=10 25.005 MEME 25.006 MEMC g's 0.20U rms #! Test Tol 0.2, Sys Tol 8.2e-005, TUR 2439.024 (>= 4.00). 26.001 HEAD {* Frequency Response *} 26.002 HEAD {LP FILTER = HIGH} 26.003 HEAD {Referenced to 100Hz} 26.004 HEAD Frequency Response 26.005 JMP 27.001 26.006 EVAL 27.001 DISP Set the UUT as follows: 27.001 DISP F. S. RANGE......................... 100 g 27.001 DISP CAL-OPER ........................... OPER 27.001 DISP RMS-PEAK ........................... PEAK 27.001 DISP SENSITIVITY dial ................... 10.0 27.002 DISP Disconnect the 5700 from the UUT CAL input connector, 27.002 DISP and reconnect through the 1000pF capacitor to the 27.002 DISP UUT ACCEL input. 27.003 IEEE [@1281]ACV AUTO,FILT100HZ 27.004 5700 0.707V 100H S 2W 27.005 IEEE [@1281][D5000]RDG?[I] 27.006 MATH M[1]=MEM 27.007 IEEE [@1281]ACV AUTO,FILT10HZ 27.008 5700 0.707V 10H S 2W 27.009 MEME 27.010 IEEE [@1281][D2000]RDG?[I] 27.011 MEME 27.012 MEMC V 3.000% 10H #! Test Tol 0.02121, Sys Tol 0.00048885, TUR 43.388 (>= 4.00). 28.001 5700 0.707V 400H S 2W 28.002 MATH MEM1=M[1] 28.003 IEEE [@1281]ACV AUTO,FILT100HZ 28.004 IEEE [@1281][D2000]RDG?[I] 28.005 MEME 28.006 MEMC V 3.000% 400H #! Test Tol 0.02121, Sys Tol 6.0025e-005, TUR 353.353 (>= 4.00). 29.001 5700 0.707V 1kH S 2W 29.002 MATH MEM1=M[1] 29.003 IEEE [@1281]ACV AUTO,FILT100HZ 29.004 IEEE [@1281][D2000]RDG?[I] 29.005 MEME 29.006 MEMC V 3.000% 1kH #! Test Tol 0.02121, Sys Tol 6.0025e-005, TUR 353.353 (>= 4.00). 30.001 5700 0.707V 10kH S 2W 30.002 MATH MEM1=M[1] 30.003 IEEE [@1281]ACV AUTO,FILT100HZ 30.004 IEEE [@1281][D2000]RDG?[I] 30.005 MEME 30.006 MEMC V 3.000% 10kH #! Test Tol 0.02121, Sys Tol 6.0025e-005, TUR 353.353 (>= 4.00). 31.001 HEAD {LP FILTER = MED} 31.002 HEAD {Referenced to 100Hz} 31.003 HEAD Frequency Response 31.004 JMP 32.001 31.005 EVAL 32.001 DISP Set the UUT as follows: 32.001 DISP LP FILTER .......................... MED 32.002 IEEE [@1281]ACV AUTO,FILT100HZ 32.003 5700 0.707V 100H S 2W 32.004 IEEE [@1281][D5000]RDG?[I] 32.005 MATH M[1]=MEM 32.006 IEEE [@1281]ACV AUTO,FILT10HZ 32.007 5700 0.707V 10H S 2W 32.008 MEME 32.009 IEEE [@1281][D2000]RDG?[I] 32.010 MEME 32.011 MEMC V 3.000% 10H #! Test Tol 0.02121, Sys Tol 0.00048885, TUR 43.388 (>= 4.00). 33.001 IEEE [@1281]ACV AUTO,FILT100HZ 33.002 5700 0.707V 400H S 2W 33.003 MATH MEM1=M[1] 33.004 IEEE [@1281][D2000]RDG?[I] 33.005 MEME 33.006 MEMC V 3.000% 400H #! Test Tol 0.02121, Sys Tol 6.0025e-005, TUR 353.353 (>= 4.00). 34.001 5700 0.707V 1kH S 2W 34.002 MATH MEM1=M[1] 34.003 IEEE [@1281][D2000]RDG?[I] 34.004 MEME 34.005 MEMC V 3.000% 1kH #! Test Tol 0.02121, Sys Tol 6.0025e-005, TUR 353.353 (>= 4.00). 35.001 5700 0.707V 2kH S 2W 35.002 MATH MEM1=M[1] 35.003 IEEE [@1281][D2000]RDG?[I] 35.004 MEME 35.005 MEMC V 3.000% 2kH #! Test Tol 0.02121, Sys Tol 6.0025e-005, TUR 353.353 (>= 4.00). 36.001 HEAD {LP FILTER = LOW} 36.002 HEAD {Referenced to 60Hz} 36.003 HEAD Frequency Response 36.004 JMP 37.001 36.005 EVAL 37.001 DISP Set the UUT as follows: 37.001 DISP LP FILTER .......................... LOW 37.002 IEEE [@1281]ACV AUTO,FILT10HZ 37.003 5700 0.707V 60H S 2W 37.004 IEEE [@1281][D5000]RDG?[I] 37.005 MATH M[1]=MEM 37.006 5700 0.707V 10H S 2W 37.007 MEME 37.008 IEEE [@1281][D2000]RDG?[I] 37.009 MEME 37.010 MEMC V 3.000% 10H #! Test Tol 0.02121, Sys Tol 0.00048885, TUR 43.388 (>= 4.00). 38.001 5700 0.707V 30H S 2W 38.002 MATH MEM1=M[1] 38.003 IEEE [@1281][D2000]RDG?[I] 38.004 MEME 38.005 MEMC V 3.000% 30H #! Test Tol 0.02121, Sys Tol 0.00015019, TUR 141.221 (>= 4.00). 39.001 5700 0.707V 70H S 2W 39.002 MATH MEM1=M[1] 39.003 IEEE [@1281]ACV AUTO,FILT40HZ 39.004 IEEE [@1281][D2000]RDG?[I] 39.005 MEME 39.006 MEMC V 3.000% 70H #! Test Tol 0.02121, Sys Tol 6.0025e-005, TUR 353.353 (>= 4.00). 40.001 5700 0.707V 100H S 2W 40.002 MATH MEM1=M[1] 40.003 IEEE [@1281]ACV AUTO,FILT100HZ 40.004 IEEE [@1281][D2000]RDG?[I] 40.005 MEME 40.006 MEMC V 3.000% 100H #! Test Tol 0.02121, Sys Tol 6.0025e-005, TUR 353.353 (>= 4.00). 41.001 DISP Disconnect the UUT from the power source 41.001 DISP and all test equipment 41.002 END #! T.U.R.s less than 4.00: 0 #! T.U.R.s estimated using RANGE value: 0 #! T.U.R.s not calculated (ASK- U): 0 #! T.U.R.s not computable at compile time: 0 #! FOR JUSTIFICATION REFER TO COMMENTS FOLLOWING EACH TEST IN THIS LISTING.